AgGPS EZ-Guide Plus Lightbar Guidance System Quick Reference Card

AgGPS® EZ-Guide® Plus Lightbar Guidance System Quick Reference Card USER INTERFACE Main screen items Status text Action icons To select an action icon, press u or D and then press o. Icon Action icon bar Tips 9 A B 8 D 1 3 2 4 5 7 Description Reset guidance Set Point A Set Point B Start headland Final headland Nudge left Nudge right Pause/Resume Change views Zoom Go to main configuration menu Views Select 4 to change between the four views shown below. Plan map Perspective map Status Offline Zooming To enter zoom mode, select 5, or press z on the remote control. • • To change the zoom scale, press u or D. To accept the zoom scale and return to the map view, press o or z on the remote control. AgGPS® EZ-Guide® Plus Lightbar Guidance System Quick Reference Card GUIDANCE AB Line Map a straight AB Line for guidance. You can reset the B point until you drive 1/2 swath offline from the AB Line. B Adaptive Curve Auto-detect turn = On The end of the swath is automatically detected when you do a U-turn. If Auto-detect turn = Off, you must press B at the end of every pass. A A A+ The heading of the AB line equals the previous AB heading or the manually entered heading. Spiral Set Auto-detect turn = Off. You must press B at the end of every pass before you start the turn to mark the end of the swath. A A B BB B B Headland Straight swaths automatically fill the headland boundary. The AB Line does not need to be the full length of the field. Before you reach the circle around the start point, press D to indicate the current headland circuit is the final circuit. You can do either a single headland or a multiple headland. D 8 A C-clamp Bold lines indicate where you must drive swaths without guidance and thin lines indicate where you get guidance. B A B B B Rowfinder Set Auto-detect turn = Off. You must press B at the end of every pass to start counting rows. 8 D A B A B B Center-pivot To work from the center of the field outwards, the initial pivot must have: • a radius of at least two swath widths Identical curve A B This pattern does not incorporate any deviation around an obstacle. B A • an arc length of at least two swath widths AgGPS® EZ-Guide® Plus Lightbar Guidance System Quick Reference Card CONFIGURATION OPTIONS Menu EZ-Steer/ Autopilot Terrain Comp. Option Description Configure an AgGPS® EZ-Steer™ assisted steering system or AgGPS Autopilot™ automated steering system (if attached). If neither is attached, the EZ-Steer menu appears. Floor – EZ-Steer controller installed on rear wall with connectors facing the floor. Front – EZ-Steer controller installed on floor with connectors facing front. Back – EZ-Steer controller installed on floor with connectors facing back. The height of the antenna above the ground (default is 0"). Run automatic Terrain Calibration sequence. Turn on or turn off screen items, such as progress lines, field boundary, or adjacent swath lines. Also used to configure view settings. Adjust the screen contrast and backlight brightness. Adjust the lightbar LED brightness. The distance from the antenna to the implement toolbar or spray boom. Upright – Inverted – Inverts the display and offline LEDs. Configure the status text items for the map views and the Status screen. Configure the input and output for the data port. Orientation Lightbar Antenna Height Calibration Display Config Contrast/ Brightness Ant/Impl. Offset Lightbar Mount Status Text Data Port Settings Pulse Output Units Guidance Configure pulse output rate. US – Feet, miles per hour, acres. Metric – Meters, kilometers per hour, hectares. Language Configure operating language for the system. Tests Run self-, button, LED, LCD, backlight, or GPS status tests. LED Mode Chase – Chase the lights to stay online. The lights represent the swath location relative to the vehicle. Pull – Center the lights to stay online. The lights represent the vehicle location relative to the swath. LED Spacing The distance represented by one LED. Look Ahead Look ahead time in seconds. Use this to allow for reaction time and vehicle turn speed. For example, at 13-24 kph (8-15 mph), set the look ahead time to 2 seconds. Increase the look ahead time for larger vehicles that take longer to turn. Auto-detect Turn Enable or disable auto-detect turn for the Adaptive Curve pattern. Nudge Increment Change the amount by which Nudge changes. Reset Nudge Resets nudge back to 0. AgGPS® EZ-Guide® Plus Lightbar Guidance System Quick Reference Card CONFIGURATION OPTIONS CONTINUED Menu Warnings Option Description Headland Warning Turn on or turn off the headland warning. Configure the warning leadtime. Offline Warning Distance off-swath at which the offline warning message appears. Set to zero to disable the warning. Low Acc Warning High Acc Only – Accept only high accuracy positions. Warn Low Acc – Accept all positions, but warn when low accuracy. No Warning – Accept all positions, including less accurate positions, without warning. Audible Warning Turn on or off the audible warning alarm. GPS Diagnostics Display GPS receiver status and diagnostic information. DGPS Diagnostics Display DGPS satellite information. GPS Limits Configure GPS limits. 1 Configure GPS correction settings. Corrections 1 Configure GPS filter settings. Filter 2 View OmniSTAR VBS, HP and XP subscription status and expiry date. , Subscription Restore Defaults Return all configuration settings to factory defaults. Display lightbar version information. Enable/disable the configuration settings protection pass code. GPS Defaults About... Pass Code 1. These options are only available for the internal receiver, or for a Trimble external receiver that has Data Port Settings input configured to TSIP Receiver. 2. These options are only available on Trimble receivers that support OmniSTAR correction services. IMPLEMENT OFFSET If the vehicle has an implement that is offset to one side of the vehicle, configure an implement offset: 1. Reset guidance and then select a new guidance pattern. The Swath / Implement screen appears. 2. Select the Impl. Offset field. 3. Press u or D until the correct value is displayed. 4. Press o. Tip — If an implement offset is configured, the vehicle will correctly be displayed off the guidance line. For guidance with an implement offset, follow the three green LEDs. AgGPS® EZ-Guide® Plus Lightbar Guidance System Quick Reference Card COVERAGE AREA By default, Coverage Area is configured for display on the Status screen. To configure it for display on the plan or perspective map view, select Lightbar / Status Text. Area is calculated whenever the spray switch is on. For more information on connecting a switch, refer to the Getting Started Guide and the instructions provided with the external interface cable. To save the coverage area value during a power cycle, you must press Pause before turning off power. PATH DISPLAY By default, the path you have driven is displayed on screen as a dotted line. If you have a spray switch connected, you can display the path only when the spray switch is on. To do this, select Display Config / Path Display and choose Switch. To turn off the display of the driven path, select Display Config / Path Display and choose Off. NUDGE Select 1 or 3 to nudge the guidance line back toward the correct path. Use nudge to: • • correct for GPS position drift when returning to the field for guidance, for example after pausing correct for GPS satellite constellation changes while driving in the field Nudge is always applied to the guidance line relative to the vehicle heading. To configure the nudge increment, select Guidance / Nudge Increment. To display the total accumulated nudge perpendicular to the current vehicle heading, use Lightbar / Status Text to configure Nudge to appear on a map view or status screen. To reset the nudge distance to 0, go to the configuration menus and select Guidance / Reset Nudge. TERRAIN COMPENSATION The AgGPS EZ-Guide Plus firmware version 3.00 and later contains a new feature called terrain compensation. The feature can be used by an EZ-Steer controller that includes the T2™ terrain compensation technology. Install the EZ-Steer controller on the floor with the connectors pointing forward, on the floor with the connectors pointing backward, or on the rear wall with the connectors pointing towards the floor. To configure terrain compensation: 1. Select Terrain Compensation / Orientation and then select the direction that the connectors point. 2. Select Terrain Compensation / Antenna Height and then enter the antenna height. 3. Select Terrain Compensation / Calibration and then perform terrain compensation calibration. AgGPS® EZ-Guide® Plus Lightbar Guidance System Quick Reference Card GPS CONFIGURATION Receiver selection To select the receiver type: 1. Go to Lightbar / Data Port Settings. 2. Press u or D to choose the receiver type from the Input field: Input None TSIP Receiver External GPS Select this input for ... Lightbar’s internal GPS receiver a Trimble GPS receiver a non-Trimble GPS receiver Input Autopilot Corrections Diagnostics Select this input for ... When an AgGPS Autopilot system is connected For RTCM input from a radio For diagnostics with AgRemote Receiver configuration To configure the correction source for the receiver, select GPS / Corrections. Note — Only correction types supported by your receiver are available for selection. You cannot configure corrections for non-Trimble GPS receivers. To edit the WAAS or EGNOS satellites, change Auto Select to Edit. The lightbar integrated receiver and the AgGPS 252 receiver use the OnPath advanced filter technology. Other Trimble receivers use the PV Filter. To configure the GPS filtering, select GPS / Filter. To configure the GPS Limits, select GPS / GPS Limits. — C CAUTIONfoot.Changing any of the GPS Limits default settings can cause GPS position errors greater than one TM ADDITIONAL INFORMATION The remote control is an optional accessory that you can purchase separately. For information, contact your local AgGPS EZ-Guide Plus system reseller. C CAUTION — Do not spray the lightbar with any type of liquid as this may cause it to fail. © 1999-2005. Trimble Navigation Limited. All rights reserved. Trimble, the Globe and Triangle logo, AgGPS, and EZ-Guide are trademarks of Trimble Navigation Limited, registered in the United States Patent and Trademark Office and in other countries. Autopilot, EZ-Steer, OnPath, and T2 are trademarks of Trimble Navigation Limited. Version 3.00, Rev A. (August 2005). P/N 57050-00-ENG, Rev A